L&L TRI-CLAD

POLYESTER TAPE

L & L TRI-CLAD POLYESTER TAPE is a pressure-sensitive tape used to bridge seams in roofing insulation and construction materials. It creates a watertight seal, eliminating damage due to leaking roofs. L & L TRI-CLAD POLYESTER TAPE is a vapor barrier, which makes it an excellent choice for permanent sealing projects in controlled atmosphere environments; e.g., fumigation containment, air flow management, coolers and freezers. 

PRIMARY USES: METAL WATERPROOFING - FUMIGATION CONTAINMENT - CONTROLLED ATMOSPHERE ENVIRONMENT - AIR FLOW MANAGEMENT IN NUCLEAR POWER FACILITIES - DUST CONTROL: SEALS JOINTS AND SEAMS ON CONVEYORS, DUST COLLECTORS, ELEVATOR AND OTHER MATERIAL-HANDLING EQUIPMENT - INSULATION JOINTS AND SEAMS - MEMBRANE ROOF SEAMS - RV AND MOBILE HOMES

PRECAUTION: Surface must be clean & free of moisture and contamination. Avoid stretching during application. See manufacturers Material Safety Data Sheet. For industrial & professional use only.

TECHNICAL DATA

APPLICATION: Clean surface removing dust, dirt and moisture. Cut desired length - peel off release liner. Apply exact the first time, centering on ridge board. Guide tape to lowest or most outside edge, working back toward center of tape, removing buckles and air pockets.

APPEARANCE: White polyester fabric, over gray modified butyl rubber adhesive, backed with clear plastic release liner.

BONDING TIME: Immediate aggressive grip. 100% adhesive bond in 24 hours.

ADHESIVE: 20 mil. Modified butyl rubber

APPLICATION TEMPERATURE RANGE: +40° F to 110° F

OPERATING TEMPERATURE RANGE: -10° F to 180° F

LOW TEMPERATURE FLEXIBILITY: Passes with no cracking

TENSILE STRENGTH: Adhesive/Sealant: 445 PSI with 75% elongation

PEEL STRENGTH: 5 lbs. per linear inch

WATER RESISTANCE: Excellent. Surface must be dry before application.

SHELF LIFE: 18 months to 2 years.

PACKAGING: 50 ft. rolls in 3, 4, and 6-inch widths

 

L & L TRI-CLAD

ALUMINUM TAPE

L & L Tri-Clad Aluminum Tape is a pressure sensitive tape consisting of 2-mil. Aluminum foil surface, backed with gray butyl adhesive sealant. This tape is used for bridging seams and creating a watertight seal. It is an excellent choice for permanent roof sealing projects over metal decks, siding, tanks, and pipe insulation.

PRIMARY USES: ICBO APPROVED - ASPHALT & SOLVENT-FREE BUTYL ADHESIVE/SEALANT - NO HARMFUL VOC'S - EXCELLENT FOR FLASHING - VAPOR BARRIER - STRONG 2 MIL. ALUMINUM - EASY, FAST APPLICATION - AGGRESSIVE GRIP - REMAINS FLEXIBLE

PRECAUTION: Surface must be clean and free of moisture and contamination. Avoid stretching during application. See manufacturers Material Safety Data Sheet. For industrial & professional use.

TECHNICAL DATA

APPLICATION: Clean surface removing dirt, dust and moisture. Cut desired length-peel off release liner. Apply exactly the first time, centering on ridge board. Guide tape to lowest part of surface. Press down firmly, starting at lowest or most outside edge, working back toward center of tape, removing buckles and air pockets.

BONDING TIME: Immediate aggressive grip. Full bond in 24 hours.

BACKING: 2 mil. Aluminum foil.

ADHESIVE: 33-mi. gray elastomeric. Modified butyl rubber.

TEMPERATURES:

APPLICATION: 30° F to 110° F

OPERATING: -10° F to 180° F

LOW TEMPERATURE FLEXIBILITY: Passes with no cracking.

TENSILE STRENGTH: Adhesive/Sealant: 445PSI with 60% elongation.

PEEL STRENGTH: 6 lbs. per linear inch.

WATER RESISTANCE: Excellent. Surface must be dry before application.

SHELF LIFE: 18 months to 2 years

PACKAGING: 50 ft. rolls in 3,4,and 6-inch widths.

 

 L & L TRI-CLAD

TEDLAR TAPE

 

L&L Tri-Clad Tedlarâ Tape is a pressure-sensitive tape used to bridge seams and create a watertight seal. This tape acts as a vapor barrier which makes it an excellent choice for permanent sealing projects over metal roof, tanks, pipe insulation, RV's and metal wall seam areas where surface coating is not necessary or applicable.

PRIMARY USES: EXCELLENT FOR SEAMS - ASSURES LEAK PROOF, ATTRACTIVE RESULTS - SUPERIOR RESISTANCE TO U.V. CHEMICALS AND ENVIRONMENTAL EXTREMES - ELIMINATES MESSY PATCHING - ASPHALT & SOLVENT-FREE BUTYL ADHESIVE/SEALANT - NO HARMFUL VOC'S - STRONG 2 MIL. TEDLAR SURFACE - EASY, FAST APLICATION - AGGRESSIVE GRIP - SUPERIOR ADHESION - STAYS FLEXIBLE

PRECAUTION: Surface must be clean & free of moisture and contamination. Avoid stretching during application. See manufacturers Material Safety Data Sheet. For industrial & professional use only.

TECHNICAL DATA

APPERANCE: Non-gloss, white backing with gray adhesive sealant.

APPLICATION: Apply over clean, dry surface. Cut desired length, peel off release liner and apply to surface. DO NOT STRETCH when applying. Removal or repositioning will damage tape. Rub down with squeegee or apply heavy pressure to insure tight seal and bond.

BONDING TIME: Immediate aggressive grip. Full bond in 24 hours.

BACKING: 1.5 mil Tedlarâ Film.

ADHESIVE: 33 mil. Gray elastomeric modified butyl rubber.

TEMPERATURES:

APPLICATION: 30° F to 110° F

OPERATING LIMITS: -10° to 180° F

PEEL STRENGTH: 6 lbs. per linear inch.

LOW TEMPERATURE FLEXIBILITY: Passes with no cracking

 TENSILE STRENGTH: Adhesive/Sealant: 445 PSI (with 60% elongation)

WATER RESISTANCE: Excellent.

SHELF LIFE: 18 months to 2 years.

 

L&L COATINGS CORPORATION

5102 Santa Fe Rd.* Tampa, FL 33619-6824 * (813) 248-3704 * 800-437-8119 * Fax: (813) 247-4319

PRODUCTS / HOME